FAQ's

 

 

 

Ellsworth Adhesives har erbjuder hög servicenivå och den rätta lösningen för att uppfylla kraven i din applikation. Vi förstår att du kan ha frågor, så vi har samlat de vanligaste frågorna här nedan.

 

Om du inte kan hitta ett svar, ring oss på +46 (0) 8 681 82 80

 

Frågorna är indelade i två kategorier:

Generella frågor och tekniska frågor


 

 

FAQs

 
         
 

Generella frågor:


Kan jag köpa online?

Idag kan du endast lägga order via mail eller telefon. 

Vilka limmer kan ni leverera?

Vi kan leverera akryler, anaerober, cyanoakrylater, epoxi, smältlim, uretaner, silikoner, lösningsmedel baserade, tejp, UV-härdande och vattenbaserade.

Kan ni göra kundanpassande etiketter?

Ja det gör vi. Vi kan leverera artikelnummer, batch nummer , utgångsdatum , etc. För mer information kontakta vår kundtjänst på +46 (0)  8 681 82 80

Hur du lägger en order?

Är ni ISO certifierade?

Ja vi är ISO 9001-2008 certifierade.

Har ni lager av alla produkter?

Nej, det har vi inte. Det finns många speciella hanteringsegenskaper för de allra flesta av våra produkter, framför allt hållbarhet som gör det svårt. Men vi är villiga att hålla lager mot skriftlig avropsorder.

Kan jag lägga en avropsorder?

Ja, vi håller personligt lager mot skriftlig avropsorder.

Vad är hållbarheten på era produkter?

För specifik information om hållbarheten av en produkt, vänligen kontakta vår kundtjänst på +46 (0) 8 681 82 80

 
 


Technical FAQ's


Will my bonded parts stay together 5, 10, 20 years from now?

Testing long term durability is a difficult matter and there are many methods of accelerating bond life testing. Some of these include exposure to elevated temperature, heat fatigue, and humidity exposure. The only way to be absolutely sure that the parts will stay together for a certain time period is to age parts over that extended period of time. The best way to estimate bond aging would be to compare new products to known quantities and determine ratios of performance in elevated aging tests. The longer and more critical the bond life, the more important the testing.

What can I do about the vapours and odours given off by cyanoacrylates?

The vapours of cyanoacrylates are irritating and workers should not be exposed to them for long periods of time. In many cases the use of our "Low Odour" and "Low Bloom" products can be used to control the irritating odour.

I'm using a CA adhesive and I've got a white haze around my bond area - is it harmful and how can I remove it?

This phenomenon is known as "blooming" or "frosting". This occurs with cyanoacrylates during their cure cycle. Blooming usually occurs in the summertime when humidity is at its peak. It can also occur when a customer uses an excessive amount of accelerator, which causes a violent curing reaction with our products. In some cases, the end user doesn't allow the product to fully cure before placing the assembly in an enclosed area. This prevents the vapours from fully dissipating.

Cold temperature crystallized my catalyst, how can I use it?

Warm the catalyst in its respective shipping container to between 45-65 C until all crystals are dissolved. Mix thoroughly and allow contents to cool down to 35 C before using.

How should I select a conformal coating?

Coating selection should be based on the following factors: - Protection/reliability of the board and components under severe. environmental situations, such as temperature range, stress tolerance etc. - Processing equipment and volume of boards to be coated. - Environmental and worker safety considerations. - Need to meet UL or Mil spec listing. - Cost and disposal. - Requirements for repair.

What application methods are best for conformal coatings?

The four most popular application methods that can be used are spray, dip, brush and flow coat.

How long does it take for an anaerobic to dry?

Anaerobic adhesives do not contain solvents, which must dry. For an anaerobic adhesive to cure, it must be in contact with active metal ions and contact with oxygen eliminated. Outside of a bonded joint, anaerobic materials will not completely cure. Inside the joint, cure rates can be controlled by changing product and primer. Heat can be used to accelerate cure rate.

Why are anaerobic bottles filled half way?

Actually, there is exactly 50ml and 250ml of adhesive in each package. We fill bottles halfway because air is needed in the package to prevent the anaerobics from solidifying. Our 50ml and 250ml bottles also allow our anaerobics to breathe by allowing air to permeate through the bottles.

Should I use a primer for curing an anaerobic?

Almost all products will cure on metal surfaces without a primer. Therefore, primers are recommended for use on non-metallic surfaces with anaerobics to achieve a practical cure speed.

How long do I have to wait before I put my bonded parts into service?

It really depends on the bonding agent and substrates. Threadlocking products show evidence of cure within 15-20 minutes and can resist vibration within an hour. Instant adhesives are often put into service within seconds.

When should I use a primer or surface activator?

Working with low surface energy substrates such as plastics often requires adhesion enhancements to achieve adequate bond strength. The need for primer varies upon application. Please feel free to contact our Customer Service at +44 (0) 1355 231122.

Should I prime both surfaces?

In most cases, this is not necessary. Generally, one surface can be primed and adhesive applied either to the primed or unprimed surface. Situations requiring priming of both surfaces generally arise when very rapid cure times are desired or when bond line gaps of .015 or more exist. When using a primer, typically less is best.

What kind of surface preparation is needed for use of products?

For threadlocking and many sealing compounds, it is many times acceptable to have thin films of oil on the parts. Only the removal of heavy grease or contamination is necessary to achieve adequate adhesive performance. For structural adhesives and instant adhesives, testing must be run to determine acceptable surface treatment. Generally, the end user should try to use the least complicated surface treatment required.

What is the shelf life of your products?

Most products are guaranteed to perform within specification for a period of one year from date of manufacture. For specific information on the shelf life of a product, please contact our Customer Service at +44 (0) 1355 231122.